U channel flat blank (press brake)

Press brake profile, U (channel): the partPress brake profile, U (channel): its flat pattern with the press lines
Press brake profile, U (channel): the part and its flat pattern (the press lines dashed), at the page's default sizes.

A channel bent twice the same way. Give the sides, the web, the angle, the inside radius and the length; the blank width counts both bend allowances, and both bend lines are drawn at the bends' middles.

The flat blank of a bent U channel: its width with the bend allowances, and the two bend lines.

Sizes you enter

What you get

The exact flat pattern of the part, worked out for the sheet thickness measured on the inside, the mean or the outside, with numbered press lines, the part in 3D, its weight and cutting length, and a DXF for laser, plasma or waterjet cutting (STEP as well).

How the pattern is developed

Bending on the press brake. A profile bent on a press brake is cut as one flat blank. Its width is the sum of the straight legs plus, at each bend, the length of the neutral layer through the bend: the angle turned times (Ri + K·t). K sets where the neutral layer lies; it follows DIN 6935 from the inside radius and the thickness unless the shop gives its own K, or its bend deduction from a test bend. Each bend line is drawn at the middle of its bend, marked up or down.

Where it is used

Angles, channels, Z purlins and hat sections bent on the press brake: brackets, frames, stiffeners, cable trays, cladding and roofing trims.

Worked example

Press brake profile, U (channel) at Height a 40 mm, Web b 80 mm, Height c 40 mm, Angle at side a 90°, Angle at side c 90°, Length 300 mm, Inside radius 3 mm, K factor 0, Bend deduction 0 mm, sheet thickness 2 mm, legs measured outside, K from DIN 6935:

Blank width151.74 mm
K factor, from DIN 69350.369
Bend allowance, each bend5.87 mm
Setback, each side of a bend5 mm
Bend deduction, each bend4.13 mm
Bend lines from the first edge37.94 ↑ 90° R3, 113.81 ↑ 90° R3
Pattern size151.74 × 300 mm
Area (bbox)0.0455 m²
Press lines2
Parts1

Change any size on the page and the pattern, the press lines and these figures follow at once.

Questions

What sizes are needed to unfold a press brake profile, U (channel)?

The height a (a), web b (b), height c (c), angle at side a (A1), angle at side c (A2), length (L), inside radius (Ri), k factor (K), bend deduction (BD), plus the sheet thickness and whether the sizes are measured on the inside, the mean surface or the outside. Unfoldo checks the sizes as they are typed and says which one does not make a part.

How big is the flat pattern of a press brake profile, U (channel)?

It depends on the sizes. At Height a 40 mm, Web b 80 mm, Height c 40 mm, Angle at side a 90°, Angle at side c 90°, Length 300 mm, Inside radius 3 mm, K factor 0, Bend deduction 0 mm the pattern is 151.74 × 300 mm, in 1 part, with 2 press lines. Each pattern comes with its own size frame and area.

Does it allow for the sheet thickness?

Yes, and it has to: on a press brake the neutral layer moves toward the inside of the bend, so the mean surface is not the right length. Enter the thickness and say whether the legs are inside or outside sizes; the bend allowance follows from the inside radius and K (DIN 6935, your own K, or your bend deduction).

What files does Unfoldo give for a press brake profile, U (channel)?

A DXF with true arcs for laser, plasma and waterjet cutting software (the cut profile on one layer, the press lines and their numbers on others), a STEP model of the part, and a PDF shop drawing with the sizes and the true lengths of the press lines.

How accurate is it?

Arcs in the DXF are true arcs, and curves that are not arcs stay within 0.005 mm of the exact curve.

Is it free?

The pattern can be seen and tried free, without an account. The exact DXF, STEP and the tables come with Pro ($29 a month), the team plan or a 30-day pass ($19); every new account gets 15 days of Pro free, no card needed.

Other variants