Oval to round transition with angled top

Oval to round, Angled top: the partOval to round, Angled top: its flat pattern with the press lines
Oval to round, Angled top: the part and its flat pattern (the press lines dashed), at the page's default sizes.

A flat oval base to a round top that is tilted, for a round pipe leaving at an angle or a fan outlet on a sloping face, and can be moved off centre. Height is measured to the centre of the top.

Oval base to a round top that is tilted, and may be moved off centre.

Sizes you enter

What you get

The exact flat pattern of the part, worked out for the sheet thickness measured on the inside, the mean or the outside, with numbered press lines, the part in 3D, its weight and cutting length, and a DXF for laser, plasma or waterjet cutting (STEP as well).

How the pattern is developed

Development by triangulation. Surfaces that are neither cylinders nor cones (one end square, the other round; offset or skewed ends) are split into thin triangles between the two ends. The true length of every side is worked out in 3D and the triangles are laid down flat one after another, so the pattern closes exactly on the sheet. The press lines are the triangles’ long sides, numbered as on the shop drawing.

Where it is used

Transitions from flat oval duct to round duct or a round outlet.

Worked example

Oval to round, Angled top at Base length 1400 mm, Base width 700 mm, Top diameter 500 mm, Height to top centre 800 mm, Top angle 15°, Top offset along the length 0 mm, Top offset along the width 0 mm, sheet thickness 0 (sizes on the mean surface), 1 part, at an end, 24 press lines:

Base (mean)1,400 × 700 mm
Top diameter (mean)500 mm
Height to top centre (H)800 mm
Top angle15°
X Offset0 mm
Y Offset0 mm
Pattern size2,962.98 × 1,271.79 mm
Area (bbox)3.7683 m²
Press lines25
Parts1

Change any size on the page and the pattern, the press lines and these figures follow at once.

Questions

What sizes are needed to unfold a oval to round, Angled top?

The base length (L), base width (W), top diameter (D), height to top centre (H), top angle (α), top offset along the length (X), top offset along the width (Y), plus the sheet thickness and whether the sizes are measured on the inside, the mean surface or the outside. Unfoldo checks the sizes as they are typed and says which one does not make a part.

How big is the flat pattern of a oval to round, Angled top?

It depends on the sizes. At Base length 1400 mm, Base width 700 mm, Top diameter 500 mm, Height to top centre 800 mm, Top angle 15°, Top offset along the length 0 mm, Top offset along the width 0 mm the pattern is 2,962.98 × 1,271.79 mm, in 1 part, with 25 press lines. Each pattern comes with its own size frame and area.

Where can the seams go, and can it be cut in parts?

The oval to round, Angled top can be laid out as: 1 part, at an end; 1 part, on a flat; 2 parts, at the ends; 2 parts, on the flats; 4 parts. Several parts are drawn side by side and numbered, ready to nest.

Does it allow for the sheet thickness?

Yes. Enter the thickness and say whether each size is on the inside, the mean surface or the outside; the pattern is worked out on the mean surface, the length that does not change when the sheet is rolled or pressed.

What files does Unfoldo give for a oval to round, Angled top?

A DXF with true arcs for laser, plasma and waterjet cutting software (the cut profile on one layer, the press lines and their numbers on others), a STEP model of the part, and a PDF shop drawing with the sizes and the true lengths of the press lines.

How accurate is it?

Arcs in the DXF are true arcs, and curves that are not arcs stay within 0.005 mm of the exact curve.

Is it free?

The pattern can be seen and tried free, without an account. The exact DXF, STEP and the tables come with Pro ($29 a month), the team plan or a 30-day pass ($19); every new account gets 15 days of Pro free, no card needed.

Other variants

More in Transitions